NeverFreeze® Pipe Tracing Cable

For weather-proofing indoor and outdoor water pipes, NeverFreeze pipe tracing cable is the best defense against seasonal damage. Safeguard your home against costly repairs due burst pipes by easily installing NeverFreeze self-regulating cable. Plug-in solution with GFCI and factory-direct custom sizes are available.
  • Designed for indoor and outdoor piping
  • Safe for straight, wrap-around, and overlap applications
  • Engineered for both residential and commercial applications
  • Single cold lead wire for easy hookup
  • Self-regulating temperature reduces power output

Drops in temperature can cause damage to your pipes if not properly cared for. Burst water pipes can cause flooding, leaks, and lead to dangerous mold and mildew later . Often, it is too late for prevention once an issue occurs and the damage is done long before anyone realizes. All the strife can be avoided easily and safely with NeverFreeze pipe tracing heating cable. Prevent costly damage and exhaustive repairs by easily installing the flexible cable ahead of time. Unlike other pipe tracing cables, NeverFreeze has unlimited installation methods, is ultra-flexible, and can be crossed along the spigot valve. Self-regulating heating elements reduce power output and consumption to the lowest possible point as the ambient conditions get warmer. Systems using self-regulating elements may not completely turn off without the use of an outside control.

Installation Guide

Power Connection Kit

GFCI Kit

End Seal Kit

Spec Sheet

Maintenance Check Sheet

Do I need a special controller?
No, all you must do is plug the attached GFCI Plug into an electrical outlet. You can also connect the system to an appropriate thermostat or controller.
Does the system turn off when not required?
No. NeverFreeze® self-regulating cable adjusts to the ambient temperature around it. By adapting to the environment, it uses no unnecessary power and it is extremely energy efficient. It can idle its output to a minimum temperature but does not completely shut off on its own. To do so, you must unplug the system or install it with an appropriate controller.
Is a 120-volt system more energy efficient than a 240-volt system?
NO. The voltage does not indicate energy efficiency, watts do.
Is NeverFreeze safe on plastic pipes?
YES! NeverFreeze self-regulating cable is approved for safe use on plastic and metal pipes.
Does NeverFreeze pipe tracing cable require insulation?
NO! It is not required, but it is recommended for use with NeverFreeze heating cables. By adding insulation, the cables are less susceptible to damage and heat loss is greatly reduced.
Can NeverFreeze self-regulating heat cable go inside a wall?
NO! Electric code does not allow pipe tracing cables inside or behind walls. The system should be easily accessible for maintenance, service, and testing.
Can I install NeverFreeze pipe tracing cable myself?
YES! Although NeverFreeze self-regulating cable is extremely easy to install, NEC requires a licensed electrician to make any non plug-in electrical connections.
How much power does the NeverFreeze heating cable use?
The amount of energy the cable uses will depend on the location it is installed in, the length and the ambient temperature. The heat output adjusts according to ambient temperatures, which dictates energy consumption. The length of pipes will determine power usage. Monitoring and modifying can be done using a thermostat, timer or power meter.
Can I cut the NeverFreeze heating cable if it’s too long?
YES! You can cut the self-regulating cable to the desired length. A licensed electrician should make any terminations.
How much cable do I need?
The amount of cable you will need depends on a few different factors. Call us at 8779229869 for help or to request a quote.
How do NeverFreeze pipe tracing cables work?
NeverFreeze pipe tracing cables are self-regulating, adjusting heat output based on ambient temperature. This drastically reduces power consumption and energy costs. Through its conductive polymer core, NeverFreeze cable prevents overheating and burning, even when overlapped and over insulted.
What is the power output of NeverFreeze?
5-8 watts/linear foot @ 0 degrees F. The output varies due to the cable being self-regulating. It will adjust its power continuously as the ambient temperature changes.
Can the cable be left out all year long?
The cable can be left on the house. However, it should not be operated above 50°F (10°C).
1 Cable
2 Snow Melt Controllers & Sensors
3 Electrical Accessories
Choose Rated Voltage:
Show 1 – 5 out of 5
Filter and sort
Clear all
Note: If you require multiple quantities of the same Cable Power product, please add each individually to your cart by returning to this page as needed.
    Cable Power Price per Ft. Length(ft.)
    5W/Ft
    		$7.00
    Ft.
    5W/Ft
    		$7.00
    Ft.
    8W/Ft
    		$7.00
    Ft.
    8W/Ft
    		$7.00
    Ft.
    12W/Ft
    		$7.00
    Ft.

    Call 800.308.8057

    Speak to a ThermoSoft radiant heat expert. For help choosing or project planning, call us or schedule a call.

    Schedule Call
Cable
2 Snow Melt Controllers & Sensors
3 Electrical Accessories
Snow Melt Controllers & Sensors
Choose Setting

Basic

Standard

Premium

  • 1 Zone Outdoor Roof/Ground Controller with Remote sensor
    1 Zone Outdoor Roof/Ground Controller with Remote sensor
    ASE-DS-8C
    $472.50 View
  • 2 Zone Outdoor Roof/Ground Controller with Remote sensor
    2 Zone Outdoor Roof/Ground Controller with Remote sensor
    ASE-DS-9C
    $502.50 View
  • Wall-mounted Remote Control/Status Panel
    Wall-mounted Remote Control/Status Panel
    ASE-CDP-2
    $156.25 View
  • GFPE protection for one 120/208/240VAC circuit up to 60A
    GFPE protection for one 120/208/240VAC circuit up to 60A
    ASE-GF-1
    $351.25 View
  • GFPE protection for two 120/208/240VAC circuits up to 60A
    GFPE protection for two 120/208/240VAC circuits up to 60A
    ASE-GF-2
    $490.00 View
  • OJ Advanced Outdoor Heat Controller
    OJ Advanced Outdoor Heat Controller
    ETO2-4550-US28
    $749.00 View
  • OJ Gutter Moisture Sensor
    OJ Gutter Moisture Sensor
    ETOR-55-US224
    $262.99 View
  • OJ Outdoor Air Temperature Sensor
    OJ Outdoor Air Temperature Sensor
    ETF-744/99
    $73.99 View
  • Outdoor approved power distribution box with GFEP (1 x 2 Pole 30A)
    Outdoor approved power distribution box with GFEP (1 x 2 Pole 30A)
    MT-PYROBOX-1X2P
    $1,270.00 View
  • Outdoor approved power distribution box with GFEP (2 x 3 Pole 50A)
    Outdoor approved power distribution box with GFEP (2 x 3 Pole 50A)
    MT-PYROBOX-2X3P
    $4,500.00 View
  • "All In One” Snow Sensor & Controller
    "All In One” Snow Sensor & Controller
    MT-PYROSELF24-X
    $1,050.00 View

    • Choose Other Components:

  • Factory Connection for Roof and Gutter. Includes Parts and Labor
    Factory Connection for Roof and Gutter. Includes Parts and Labor
    NF-GPPCK-FC
    $100.00 View
  • Hardwired Power Connection Kit
    Hardwired Power Connection Kit
    NF-PCK
    $24.95 View
  • Hanger Bracket
    Hanger Bracket
    NF-HB
    $12.95 View
  • End Seal Kit
    End Seal Kit
    NF-ESK
    $10.95 View
    • Cable
    Snow Melt Controllers & Sensors
    3 Electrical Accessories
    Electrical Accessories
  • Quick Connect Power Cord
    Quick Connect Power Cord
    NFC-C-PCK
    $149.95 View
  • Quick Connect Splice Kit
    Quick Connect Splice Kit
    NFC-C-SK
    $134.95 View
  • Quick Connect Lighted End
    Quick Connect Lighted End
    NFC-C-LE
    $159.95 View
  • Compact Junction Box
    Compact Junction Box
    NFC-I-PCK
    $169.95 View
  • Compact Splice Kit
    Compact Splice Kit
    NFC-I-SK
    $54.95 View
  • Compact End Seal Kit
    Compact End Seal Kit
    NFC-I-ES
    $19.95 View
  • Black Low-Profile Tee Connection Kit. Industrial application.
    Black Low-Profile Tee Connection Kit. Industrial application.
    NFC-I-TKIT-1
    $28.00 View

    • This is the last step

    See your cart
    • Designed for indoor and outdoor piping
    • Safe for straight, wrap-around, and overlap applications
    • Engineered for both residential and commercial applications
    • Single cold lead wire for easy hookup
    • Self-regulating temperature reduces power output

    Drops in temperature can cause damage to your pipes if not properly cared for. Burst water pipes can cause flooding, leaks, and lead to dangerous mold and mildew later . Often, it is too late for prevention once an issue occurs and the damage is done long before anyone realizes. All the strife can be avoided easily and safely with NeverFreeze pipe tracing heating cable. Prevent costly damage and exhaustive repairs by easily installing the flexible cable ahead of time. Unlike other pipe tracing cables, NeverFreeze has unlimited installation methods, is ultra-flexible, and can be crossed along the spigot valve. Self-regulating heating elements reduce power output and consumption to the lowest possible point as the ambient conditions get warmer. Systems using self-regulating elements may not completely turn off without the use of an outside control.

    Installation Guide

    Power Connection Kit

    GFCI Kit

    End Seal Kit

    Spec Sheet

    Maintenance Check Sheet

    Do I need a special controller?
    No, all you must do is plug the attached GFCI Plug into an electrical outlet. You can also connect the system to an appropriate thermostat or controller.
    Does the system turn off when not required?
    No. NeverFreeze® self-regulating cable adjusts to the ambient temperature around it. By adapting to the environment, it uses no unnecessary power and it is extremely energy efficient. It can idle its output to a minimum temperature but does not completely shut off on its own. To do so, you must unplug the system or install it with an appropriate controller.
    Is a 120-volt system more energy efficient than a 240-volt system?
    NO. The voltage does not indicate energy efficiency, watts do.
    Is NeverFreeze safe on plastic pipes?
    YES! NeverFreeze self-regulating cable is approved for safe use on plastic and metal pipes.
    Does NeverFreeze pipe tracing cable require insulation?
    NO! It is not required, but it is recommended for use with NeverFreeze heating cables. By adding insulation, the cables are less susceptible to damage and heat loss is greatly reduced.
    Can NeverFreeze self-regulating heat cable go inside a wall?
    NO! Electric code does not allow pipe tracing cables inside or behind walls. The system should be easily accessible for maintenance, service, and testing.
    Can I install NeverFreeze pipe tracing cable myself?
    YES! Although NeverFreeze self-regulating cable is extremely easy to install, NEC requires a licensed electrician to make any non plug-in electrical connections.
    How much power does the NeverFreeze heating cable use?
    The amount of energy the cable uses will depend on the location it is installed in, the length and the ambient temperature. The heat output adjusts according to ambient temperatures, which dictates energy consumption. The length of pipes will determine power usage. Monitoring and modifying can be done using a thermostat, timer or power meter.
    Can I cut the NeverFreeze heating cable if it’s too long?
    YES! You can cut the self-regulating cable to the desired length. A licensed electrician should make any terminations.
    How much cable do I need?
    The amount of cable you will need depends on a few different factors. Call us at 8779229869 for help or to request a quote.
    How do NeverFreeze pipe tracing cables work?
    NeverFreeze pipe tracing cables are self-regulating, adjusting heat output based on ambient temperature. This drastically reduces power consumption and energy costs. Through its conductive polymer core, NeverFreeze cable prevents overheating and burning, even when overlapped and over insulted.
    What is the power output of NeverFreeze?
    5-8 watts/linear foot @ 0 degrees F. The output varies due to the cable being self-regulating. It will adjust its power continuously as the ambient temperature changes.
    Can the cable be left out all year long?
    The cable can be left on the house. However, it should not be operated above 50°F (10°C).